Stainless Steel Flux cored Wires
| AWS | DIA | Description |
|---|---|---|
|
E307T1-1
|
1.20, 1.60
|
For joining manganese steel to dissimilar steels like stainless steel, carbon steel, alloy steel, difficult to weld steels & high alloys steel like armour plates, for repairing cracks in austenitic manganese steel casting, for laying buffer before handcrafting, surfacing manganese steel rails etc.
|
|
E 308HT1-1
|
1.20, 1.60
|
Used for welding of 304H, 308H type base metal.
|
|
E 308LT1-1
|
1.20, 1.60
|
Used for welding of 18% cr, 9% nickel steel for joining austenitic steels such as 304, 304I.
|
|
E 309HT1-1
|
1.20, 1.60
|
Suitable for the welding of dissimilar metals such as stainless steel and carbon steel or stainless steel and low alloy steel. Ferrite content is about 6-7 fn. For welding of 23 Cr- 12.5 Ni wrought & cast steels designed for corrosion and oxidation resistance.
|
|
E 309LT1-1
|
1.20, 1.60
|
Suitable for the welding of dissimilar metals such as stainless steel and carbon steel or stainless steel and low alloy steel.
|
|
E 309LMoT1-1
|
1.20, 1.60
|
Dissimilar joint welds of and between high strength mild steel & low alloy quenched & tempered steel stainless steel. Ferrite Cr. & Austenitic -Cr/Ni steel. Cladding fr first layer of corrosion resistant weld cladding on ferrite steels.
|
|
E 312T1-1
|
1.20, 1.60
|
Suitable for the welding of difficult to weld steel like spring steels. Cast steels, tool steels, high speed steels, case hardening steels, manganese steels steel of unknown chemical composition, dissimilar joints between stainless steel & high carbon steel.
|
|
E 316HT1-1
|
1.20, 1.60
|
Provides higher tensile and creep strength at elevated temperature. It is used for welding of 316H type base metal.
|
|
E 316LT1-1
|
1.20, 1.60
|
Used for welding of AISI 316I & 317I type of stainless steel in chemical plant, paint, pulp paper & textile industries.
|
|
E 410T0-1
|
1.20, 1.60
|
Welding of marten site stainless alloys of 13% Cr. type. It is used for surfacing of seraling faces of valves for gas, water & steam piping. Hard surfacing of continuous casting roll of steel plants, valves etc.
|
|
E 410 NIMoT0- 1/4
|
1.20, 1.60
|
It gives martensitic weld steel. It used for welding of corrosion resisting steels & castings with 12% Cr & 4.5% Ni, E410, E410s, E405 grade materials, CA6NM castings and similar materials like ASTM A352, ASTM wrought F6NM.
|
|
E 2209T0-1
|
1.20, 1.60
|
Used for welding of duplex stainless steel which contain approximately 22% chromium. Also used for joining of duplex steels to mild steels, cladding of duplex stainless steel weld metal on carbon steel/low alloy steel, welding of stainless steels 1.4417, 1.4460, 1.4462.
|
|
E 2553T0-1
|
1.20, 1.60
|
Used for welding of duplex stainless steel which contain approximately 22% chromium. Also used for joining of duplex steels to mild steels, cladding of duplex stainless steel weld metal on carbon steel/low alloy steel, welding of stainless steels 1.4417, 1.4460, 1.4462., 1.4515, 1.4517.
|
|
E 2594T0-1
|
1.20, 1.60
|
For the welding of super duplex stainless steels UNS S32750 & S32760 (wrought) & UNS J93380 & J93404 (steels). It can be used for UNS S32550, J93370 & J93372 when not subjected to sulphueous or sulphuric acids in service. For welding of low alloy steels to duplex steels such as E2205 & E2209 grades.
|